SuperTie™ systems eliminate the possibility of rust stains, as well as the structural deterioration often caused by failure of patching for steel form-tie holes. SuperTie™ 6K Patented Gripper System offers an ultimate tensile strength of 6,000 pounds (3,000 pounds safe working load at 2:1 safety factor) and is most commonly used with job-built (plywood and 2×4) forms and handset modular forms. RJD Fiberglass Smooth Rod is offered in .308” and 0.50” diameters with a selection of colors available for each size. This system's greater strength makes it attractive to those who need heavier forms and higher concrete placement rates. .308″-dia. The RJD fiberglass tie will never rust, therefore no breakback removal or snap-tie cone patching is ever required, creating superior architectural finishes. ultimate strength. The fiberglass rod diameter is 1/2” inch, making the system compatible with most commercial forming systems. SuperTie™ 15K Patented Gripper ofers an ultimate tensile strength of 15,000 pounds (7,500 pounds safe working load at 2:1 safety factor) and is most commonly used with the jobsite built (plywood and 2×4) forms and hand-set modular forms. Non-Corrosive Fiberglass Smooth Rod (.308”), Guía de Instalación (6K-Español Imperíal), Guía de Instalación (6K-Español Metrico). SuperTie™ Coil Rod Form Fixture 1” offers an ultimate tensile strength of 34,000 pounds (17,000 pounds safe working load at 2:1 safety factor) and is most commonly used with job-built (plywood and 2×4) forms and handset modular forms. (Do not use any non-RJD engineered rod with RJD grippers; this could result in form failure and/or injury.) The fiberglass rod diameter is only.308 inches, making the system compatible with most commercial forming systems. SuperTie™ systems are appropriate for use in all forming applications but are especially beneficial in situations such as architectural finishes because an aesthetically pleasing finish is attained with tremendously reduced labor expenditures. This system’s greater strength makes it attractive to those who need heavier forms and higher concrete placement rates. Invalid zip code. RJD Fiberglass Coil Rod utilizes a specially blended and formulated custom-engineered resin, made in the USA, combining ultimate tensile strength and the RJD Form Fixture (CRFF) strength. RJD Fiberglass Smooth Rod utilizes a specially blended and formulated custom-engineered resin, made in the USA, combining ultimate tensile strength and maximizing the RJD Gripper strength. Please select a product to get delivery info, 3,000 pounds safe working load at 2:1 safety factor, Most commonly used with job-built (plywood and 2x4) forms and hand-set modular forms. G50K comes with customized bearing plate (call for details). Always use 2:1 safety factor when engineering tie spacings; refer to the ACI-suggested tie spacing noted in the SuperTie Installation Guide. Longer lengths can be special ordered with only the ends threaded. The fiberglass rod diameter is only .308 inches, making the system compatible with most commercial forming systems. The fiberglass rod diameter is 3/4” inch, making the system compatible with most commercial forming systems. (Do not use any non-RJD engineered rod with RJD grippers; this could result in form failure and/or injury.) The.500-inch-diameter rod can be used with many commercially available forms. The fiberglass coil threaded rod will never rust; therefore removal from a structure (as with steel threaded rod) is not necessary. Easier to use, saves time, and less expensive than traditional steel form ties. SuperTie™ 6K (.308” Rod) GND6000 SuperTie™ 6K Patented Gripper System offers an ultimate tensile strength of 6,000 pounds (3,000 pounds safe working load at 2:1 safety factor) and is most commonly used with the job-built (plywood and 2×4) forms and hand-set modular forms. Use of this site is subject to the White Cap Supply Holdings, LLC. Compatible with most (Do not use any non-RJD engineered rod with RJD grippers; this could result in form failure and/or injury.) For custom rod lengths and/or custom colors, please call for quote and lead times. Fiberglass Coil Rod is available in ½”, ¾”, and 1” diameters, offering ultimate strengths of up to 15,000, 24,000, and 34,000 pounds. SuperTie™ patented fiberglass form-tie systems are used to secure concrete formwork during concrete placement and initial hydration, without the inherent limitations and rusting of previously popular steel form-tie systems. SuperTie Coil Rod™ secures concrete formwork during concrete placement. The Bearing Plate is a required component with the SuperTie Gripper. SuperTie™ patented fiberglass form-tie systems are used to secure concrete formwork during concrete placement and initial hydration, without the inherent limitations of previously popular steel form-tie systems. The .500-inch-diameter rod can be used with many commercially available forms. RJD fiberglass smooth rod utilizes a specially blended and formulated custom engineered resin, made in the USA, combining ultimate tensile strength and maximummizing the RJD gripper strength. SuperTie™ Coil Rod Form Fixture 3/4” offers an ultimate tensile strength of 24,000 pounds (12,000 pounds safe working load at 2:1 safety factor) and is most commonly used with job-built (plywood and 2×4) forms and handset modular forms. RJD SuperTie™ can be manufactured in a broad array of colors. RJD Industries Showing all 11 results Default sorting Sort by popularity Sort by average rating Sort by latest Sort by price: low to high Sort by price: high to low RJD Fiberglass Smooth Rod will never rust, eliminating the need for breakback, plugging, and patching and allowing for superior architectural finishes. Call for the name of the dealer nearest you. The fiberglass rod diameter is 1” inch, making the system compatible with most commercial forming systems. RJD Fiberglass Coil Rod is offered in ½”, ¾”, and 1” diameters. BP615 is a 4”x4” steel plate that fits the 6K and 15K systems.